Effect of tube-electrode inner diameter on electrochemical discharge machining of nickel-based superalloy

Nickel-based superalloys are widely employed in modern aircraft engines because of their excellent material characteristics, particularly in the fabrication of film cooling holes. How-ever, the high machining requirement of a large number of film cooling holes can be extremely chal-lenging. The hybrid machining technique of tube electrode high-speed electrochemical discharge drilling (TEHECDD) has been considered as a promising method for the production of film cooling holes. Compared with any single machining process, this hybrid technique requires the removal of more complex machining by-products, including debris produced in the electrical discharge machin-ing process and hydroxide and bubbles generated in the electrochemical machining process. These by-products significantly affect the machining efficiency and surface quality of the machined prod-ucts. In this study, tube electrodes in different inner diameters are designed and fabricated, and the effects of inner diameter on the machining efficiency and surface quality of TEHECDD are inves-tigated. The results show that larger inner diameters could effectively improve the flushing condi-tion and facilitate the removal of machining by-products. Therefore, higher material removal efficiency, surface quality, and electrode wear rate could be achieved by increasing the inner diam-eter of the tube electrode.     

某锁闭机构耐久性试验研究

为了验证某直升机用锁闭机构的耐久性能，在没有现行标准的情况下，作者采用逐步加载的方法确定预紧力进行耐久性试验，该方法为耐久性试验的具体实施提供了一种解决思路。     

高温升直流燃烧室燃烧特性数值研究

为了研究高温升直流燃烧室燃烧特性,建立了带三级涡流器的高温升直流燃烧室物理模型,采用稳态雷诺平均N-S方程的化学反应流数值模拟的方法,开展Ⅱ、Ⅲ级径向涡流器旋向、主燃孔和掺混孔特征参数对高温升直流燃烧室的流场及燃烧特性的影响研究。涡流器能够实现火焰筒头部回流区的产生,同时实现主油路燃油的气动雾化和掺混。主燃孔的射流影响回流区的结构,同时主燃孔射流部分进入主燃区,能够保证主燃区的油气比。掺混孔的射流轨迹影响掺混区的流场和出口温度分布。10种方案燃烧室的温升和总压损失系数均达到设计要求,Mode-1-tx、Mode-3、Mode-3-tx、Mode-4-tx四种方案燃烧室周向温度分布系数(Overall temperature distribution factor,OTDF)达标,而径向温度分布系数(Radial temperature distribution factor,RTDF)略高于设计指标,Mode-5-tx方案燃烧室出口温度系数OTDF=0.178和RTDF=0.061均达标,燃烧室出口温度分布品质较好。     

自循环吸附动叶设计原理及数值模拟分析

研究了一种新型自循环吸附动叶,分析了其主要实现结构以及自循环吸附的原理。新型吸附结构利用动叶旋转离心作用形成的驱动力抑制了叶表分离、叶顶二次流动,增加了叶顶附面层动量,提高了动叶效率及稳定裕度。通过与传统的机匣处理技术的对比,阐明了自循环吸附动叶的独特结构以及叶顶喷气技术优势。以Rotor37动叶为例,依据基本的吸气、喷气原则,开展了吸气槽、叶顶喷气孔以及动叶内腔等自循环典型结构概念方案设计,突破了带有动叶内腔的复杂网格生成技术,完成了自循环吸附动叶内腔以及叶片通道内的流动分析以及特性分析。研究结果表明:自循环吸附技术优势明显,数值模拟证明其原理可行。     

Capillary flow rate limitation in asymmetry open channel

This paper focuses on the stability of capillary forced flow.In space,open capillary channels are widely used as the liquid and gas separation devices to manage liquid positioning and transportation.Surface collapse happens when the flow rate exceeds the critical value,leading to a failure of propellant management.Knowledge of flow rate limitation is of great significance in design and optimization of propellant management devices(PMDs).However,the capillary flow rate limitation in an asymmetry channel has not been studied yet in the literature.In this paper,by introducing an equivalent angle to convert the asymmetry corner to a symmetry one,the one-dimensional theoretical model is developed.The flow rate limitation can then be investigated as a function of the channel geometry as well as liquid property based on the model.Comparisons between the asymmetry and symmetry channels bring forth the characteristics of the two kinds of channels,and demonstrate good accordance between the new advanced model and the existing one in the literature.This theoretical model can provide valuable reference for PMD designers.     

张力腿漂浮式风力机的运动响应计算

漂浮式风力机与近海桩基式风力机、陆上风力机差异很大,特别是漂浮平台设计复杂,对仿真工具要求更高。海上风力机除受气动载荷之外,还需进一步考虑海洋环境所施加的各种其他载荷。采用自由涡尾迹方法计算风力机气动性能,分别采用线性波和PM频谱模拟波浪运动并应用Morison方程计算波浪载荷。构建张力腿漂浮平台结构动力学方程,以气动载荷和波浪载荷为激励,得到平台响应,并反馈至气动计算,从而完成气动、结构和水动的耦合计算。最后以大型风力机NH1500为例,对张力腿式海上风力机进行仿真模拟,对比分析来流风速、浪高和波浪入流角对漂浮平台运动和风力机气动性能的影响,采用PM频谱模拟真实海况并计算漂浮式风力机动态响应,为漂浮式风力机设计提供了依据。     

活门型孔“化方为圆”算法

通过对航空发动机控制系统活门型孔的流量系数稳定性控制的方法进行研究,提出了一套能够将方形活门型孔转化为有规律排列组合小圆孔的算法,并通过实例验证了算法的正确性,同时转化误差小于0.7%,基本实现了工程意义上的等流量系数。该算法将加工工艺性差且计量精度低的方形活门型孔转化为有规律排列组合小圆孔,消除了方形型孔流量系数变化的影响,改变了活门型孔加工方法,减少了对人和环境的危害,提高了活门型孔的计量精度,减小了活门的液动力,具有极大的工程应用价值。 该算法可以实现将方形、梯形（含三角形）及其组合型孔等任意型孔的转化,具有工程上的普遍适用性。     

下缘板孔对涡轮叶片尾缘内冷通道流动换热影响的数值研究

涡轮叶片下缘板出气孔对内冷通道的流动和换热性能有较大影响。通过数值模拟方法研究下缘板出 气孔对尾缘和下缘板双路出气涡轮叶片尾缘内冷通道内的流动和换热特性,对比分析孔径、孔形和孔位置对尾 缘溢流孔流量系数、尾缘出流比、尾缘通道内总压系数和尾缘内冷腔壁面换热特性的影响。结果表明:下缘板 出气孔孔径对流量系数分布的影响显著,孔径增大,尾缘溢流孔流量系数下降,尾缘出流比减小,尾缘内冷通道 内压力损失降低,内冷腔平均换热系数增大;孔形对上游内冷通道内流动和换热几乎没有影响;孔位置变化对 内冷通道壁面整体的换热系数影响很小,对局部影响较大。     

含孔边裂纹各向异性有限板的二维问题

应用边界元法，并结合一种特殊的复变函数基本解，研究了含孔边裂纹的各向异性有限板的应力强度因子修正系数的计算。这种特解边界元法避免了在裂纹附近划分单元，可以获得较好的数值计算精度。通过算例分析，结果表明本方法精度高，运算量小，具有一定的工程应用价值。     

基于Kriging模型插值的孔位修正策略

飞机装配时的孔位精度直接影响其最终装配质量，而待制孔零件易发生变形和整体偏移，因此一般通过基准孔信息对待制孔位进行补偿。提出一种基于Kriging插值的孔位修正方法，通过基准孔建立孔位理论坐标与实际偏差值的Kriging模型，进而预测待制孔的孔位偏差，并给出每个位置的预测标准误差，以指导基准孔的增添和布置。最后通过有限元和数值实验分别验证了零件在极限变形和整体平移旋转情况下该方法的有效性，实现了孔位估计误差小于0.3 mm。